联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
端子机的检验方式
检测端子机是否合格，需要通过端子截面分析仪，过程分为：切割----磨抛----电解（腐蚀）----观察。
To test whether the terminal machine is qualified or not, it is necessary to use the terminal section analyzer. The process is divided into cutting, polishing, electrolysis (corrosion) - observation.
1、剥皮开口长度不一：
1. The length of peeling opening is different:
导致开口不一的原因有很多最常见的如送线轮压得过紧或松；这时候你只需要用滚线轮微调件调整两轮之间空隙以至线材不压扁和太松打滑。如果是因为切剥刀切入太浅或太深；那么我们就用切刀深浅调节件来调试刀口到适当位置，以不伤铜丝且能顺利脱落胶皮为准。如果还是开口不一的话，那就直接更换新切刀片。
There are many common reasons for different openings, such as too tight or loose wire feeding wheels; at this time, you only need to adjust the gap between the two wheels with a fine-tuning roller, so that the wire does not flatten and skid too loosely. If the cutter cuts too shallowly or too deep, then we use the cutter depth adjuster to adjust the knife edge to the appropriate position, so as not to hurt the copper wire and can smoothly peel off the rubber. If the opening is different, replace the new blade directly.
2、压着端子露铜丝不均：
2. Pressing terminal copper wire unevenly:
检查枪型摆臂导管是否与线材相附合；端子机刀口是否与摆臂导管相对直；端子机辅助压块是否松动；检查端子机与自动机之间的距离有无变动。
Check whether the gun-type swing arm conduit is attached to the wire rod; whether the knife edge of the terminal machine is relatively straight with the swing arm conduit; whether the auxiliary pressing block of the terminal machine is loose; check whether the distance between the terminal machine and the automation has changed.
3、端子机无法启动运转或运转中停止：
3. Terminals can not start or stop in operation:
无法启动或者运转中停止，首先要坚检查是否有无电流输入及6KG气压以及有无线材或某运转部位卡住；还有检查端子机有无信号连接或电源连接而导至端子机器不压着。
Can not start or stop in operation, first of all, we must check whether there is no current input and 6KG air pressure, as well as whether there is wireless material or a certain part of the operation jammed; and check whether there is signal connection or power connection to the terminal machine and lead to the terminal machine not pressed.
4、端子机的电子线切断长度不一致：
4. The cut-off length of the electronic wire of the terminal machine is different:
可能是切线刀口磨损或刀口刃；碰到这样的问题很简单就是更换新切刀。也可能的原因是因为送线轮压得过紧或过松；这时候我们可以用滚线轮微调件调整两轮之间空隙以至线材不压扁和太松打滑。
It may be that the cutting edge is worn or the cutting edge is worn; it's easy to replace a new cutting tool when you encounter such a problem. It may also be that the feeder wheel is too tight or too loose; at this time, we can adjust the gap between the two wheels with the roller fine-tuning parts so that the wire is not flattened or too loose and slippery.
To test whether the terminal machine is qualified or not, it is necessary to use the terminal section analyzer. The process is divided into cutting, polishing, electrolysis (corrosion) - observation.
1、剥皮开口长度不一：
1. The length of peeling opening is different:
导致开口不一的原因有很多最常见的如送线轮压得过紧或松；这时候你只需要用滚线轮微调件调整两轮之间空隙以至线材不压扁和太松打滑。如果是因为切剥刀切入太浅或太深；那么我们就用切刀深浅调节件来调试刀口到适当位置，以不伤铜丝且能顺利脱落胶皮为准。如果还是开口不一的话，那就直接更换新切刀片。
There are many common reasons for different openings, such as too tight or loose wire feeding wheels; at this time, you only need to adjust the gap between the two wheels with a fine-tuning roller, so that the wire does not flatten and skid too loosely. If the cutter cuts too shallowly or too deep, then we use the cutter depth adjuster to adjust the knife edge to the appropriate position, so as not to hurt the copper wire and can smoothly peel off the rubber. If the opening is different, replace the new blade directly.
2、压着端子露铜丝不均：
2. Pressing terminal copper wire unevenly:
检查枪型摆臂导管是否与线材相附合；端子机刀口是否与摆臂导管相对直；端子机辅助压块是否松动；检查端子机与自动机之间的距离有无变动。
Check whether the gun-type swing arm conduit is attached to the wire rod; whether the knife edge of the terminal machine is relatively straight with the swing arm conduit; whether the auxiliary pressing block of the terminal machine is loose; check whether the distance between the terminal machine and the automation has changed.
3、端子机无法启动运转或运转中停止：
3. Terminals can not start or stop in operation:
无法启动或者运转中停止，首先要坚检查是否有无电流输入及6KG气压以及有无线材或某运转部位卡住；还有检查端子机有无信号连接或电源连接而导至端子机器不压着。
Can not start or stop in operation, first of all, we must check whether there is no current input and 6KG air pressure, as well as whether there is wireless material or a certain part of the operation jammed; and check whether there is signal connection or power connection to the terminal machine and lead to the terminal machine not pressed.
4、端子机的电子线切断长度不一致：
4. The cut-off length of the electronic wire of the terminal machine is different:
可能是切线刀口磨损或刀口刃；碰到这样的问题很简单就是更换新切刀。也可能的原因是因为送线轮压得过紧或过松；这时候我们可以用滚线轮微调件调整两轮之间空隙以至线材不压扁和太松打滑。
It may be that the cutting edge is worn or the cutting edge is worn; it's easy to replace a new cutting tool when you encounter such a problem. It may also be that the feeder wheel is too tight or too loose; at this time, we can adjust the gap between the two wheels with the roller fine-tuning parts so that the wire is not flattened or too loose and slippery.
